Skip to main content

FREE SHIPPING from € 100,- / DE / AT

FREE SHIPPING: DE, AT... from 100,- € / CH ... from 199,- / FR, BE, BG, FR, IT, HR, NL ... from 299,- €

FREE SHIPPING from € 100,- / DE / AT

CNC-milled balsa and plywood parts, carbon tubes for wing main spars, carbon rear boom, accessory set, decal sheet, full-size construction plan, operating instructions.

Wing-span (mm): 1498
Flight weight approx. (g): 260 ohne Akku
Empty weight approx. (g): 230
Control: H,S,Q
Length (mm): 1070
Manufacturer: KAVAN
Fuselage: Wood
Wings: Wood
Rec. Battery: 500-600mAh LiXX
Version: KIT
Flight Skill: Advanced
Build Skill: Advanced
Drive Type: Glider

of balsa and sticks”, you should not have any problems. There should be no problems mastering the discus launch once your STRIKE DLG is ready to fly as well - we included a thorough illustrated appendix showing how it is done in the instruction manual.

Designed and manufactured in the Czech Republic.

This builder’s kit of a high-performance RC hand launch glider is a perfect project for a modeller wanting to build a really good for sporty and “Sunday“ flying. The well-thought design with CNC-cut interlocking parts fitting together like jigsaw puzzle pieces makes the building a breeze. The ribs and riblets are supplied with jig tabs allowing building the wing (featuring an under-cambered profile) directly on a flat working surface - and all that with a built-in washout!

The front part of the fuselage is a simple „box“ of balsa sides, top and bottom sheets and plywood formers and braces. The servo and battery compartment is located in the front part under the removable hatch with a magnetic lock. The tail boom is a carbon tube with liteply pylon for the horizontal tailplane. The tow hook for the bungee launch is also included in the kit.

The one-piece wing sports the YA0801 wing section (“tailored” to the needs of RC hand launch gliders) is off, now we can say classic, design with CNC-cut balsa ribs, carbon tube main spar and beech dowel leading edge for high strength at very low weight. The full-span ailerons are controlled by two servos installed in the wing. The wing is secured to the fuselage with a plastic bolt. The discus launch pin can be installed on the left wing tip (for right-handed pilots) or to the right wing tip (for left-handed pilots).

The empennage is made of CNC-cut balsa sheets with balsa and carbon reinforcements. The elevator and rudder are controlled by servos located in the fuselage with piano wire push rods running through the tail boom.

You can use an iron-on film for covering - lightweight Oralight® or similar materials are preferred.

You will need at least four channel radio to control your STRIKE DLG. A computer radio is preferred; it will allow setting aileron differential, airbrakes as well as mixes making the discus launch much easier. Good 6 g micro servos (0.7–0.9 kg­·cm torque) are required for the ailerons, elevator and rudder; the servo trays supplied in the kit are tailored to the KAVAN GO-6MG servos.

1S 3.7 V 500–600 mAh LiPo battery would make a great receiver battery.

The product Strike DLG 1498mm kit from KAVAN in the category Glider Models has a wingspan of 1498 and a weight of 230. The model is controlled via the functions H,S,Q*. The Model is Holz .

* Explanation of control functions:
  • H ... Elevator
  • S ... Rudder
  • Q ... Ailerons
  • M ... Motor controlled
  • V ... Vector controlled
  • SK ... Airbrakes
  • WK ... Flaps
  • WZFW ... Retractable Landing Gear
  • SKU ... Glider Tow
  • ( ) ... optional - control functions written in brackets are optionally available for the described model

Manufacturer and responsible person (information obligations under the GPSR Product Safety Regulation)

KAVAN Europe s.r.o.
Doubravice 110
53353 PARDUBICE
TSCHECHISCHE REPUBLIK
Tel: +420466260133
[email protected]

KAVAN Strike DLG 1498mm kit
Product number: 9800318
Manufacturer number: KAV02.8024

€139.99*

In stock. Usually ships within 1 business day.

CNC-milled balsa and plywood parts, carbon tubes for wing main spars, carbon rear boom, accessory set, decal sheet, full-size construction plan, operating instructions.

Wing-span (mm): 1498
Flight weight approx. (g): 260 ohne Akku
Empty weight approx. (g): 230
Control: H,S,Q
Length (mm): 1070
Manufacturer: KAVAN
Fuselage: Wood
Wings: Wood
Rec. Battery: 500-600mAh LiXX
Version: KIT
Flight Skill: Advanced
Build Skill: Advanced
Drive Type: Glider

of balsa and sticks”, you should not have any problems. There should be no problems mastering the discus launch once your STRIKE DLG is ready to fly as well - we included a thorough illustrated appendix showing how it is done in the instruction manual.

Designed and manufactured in the Czech Republic.

This builder’s kit of a high-performance RC hand launch glider is a perfect project for a modeller wanting to build a really good for sporty and “Sunday“ flying. The well-thought design with CNC-cut interlocking parts fitting together like jigsaw puzzle pieces makes the building a breeze. The ribs and riblets are supplied with jig tabs allowing building the wing (featuring an under-cambered profile) directly on a flat working surface - and all that with a built-in washout!

The front part of the fuselage is a simple „box“ of balsa sides, top and bottom sheets and plywood formers and braces. The servo and battery compartment is located in the front part under the removable hatch with a magnetic lock. The tail boom is a carbon tube with liteply pylon for the horizontal tailplane. The tow hook for the bungee launch is also included in the kit.

The one-piece wing sports the YA0801 wing section (“tailored” to the needs of RC hand launch gliders) is off, now we can say classic, design with CNC-cut balsa ribs, carbon tube main spar and beech dowel leading edge for high strength at very low weight. The full-span ailerons are controlled by two servos installed in the wing. The wing is secured to the fuselage with a plastic bolt. The discus launch pin can be installed on the left wing tip (for right-handed pilots) or to the right wing tip (for left-handed pilots).

The empennage is made of CNC-cut balsa sheets with balsa and carbon reinforcements. The elevator and rudder are controlled by servos located in the fuselage with piano wire push rods running through the tail boom.

You can use an iron-on film for covering - lightweight Oralight® or similar materials are preferred.

You will need at least four channel radio to control your STRIKE DLG. A computer radio is preferred; it will allow setting aileron differential, airbrakes as well as mixes making the discus launch much easier. Good 6 g micro servos (0.7–0.9 kg­·cm torque) are required for the ailerons, elevator and rudder; the servo trays supplied in the kit are tailored to the KAVAN GO-6MG servos.

1S 3.7 V 500–600 mAh LiPo battery would make a great receiver battery.

The product Strike DLG 1498mm kit from KAVAN in the category Glider Models has a wingspan of 1498 and a weight of 230. The model is controlled via the functions H,S,Q*. The Model is Holz .

* Explanation of control functions:
  • H ... Elevator
  • S ... Rudder
  • Q ... Ailerons
  • M ... Motor controlled
  • V ... Vector controlled
  • SK ... Airbrakes
  • WK ... Flaps
  • WZFW ... Retractable Landing Gear
  • SKU ... Glider Tow
  • ( ) ... optional - control functions written in brackets are optionally available for the described model

Manufacturer and responsible person (information obligations under the GPSR Product Safety Regulation)

KAVAN Europe s.r.o.
Doubravice 110
53353 PARDUBICE
TSCHECHISCHE REPUBLIK
Tel: +420466260133
[email protected]