Skip to main content

FREE SHIPPING from € 100,- / DE / AT

FREE SHIPPING: DE, AT... from 100,- € / CH ... from 199,- / FR, BE, BG, FR, IT, HR, NL ... from 299,- €

FREE SHIPPING from € 100,- / DE / AT

Small Rotary
Rotary Domehead Fine finishing Grit, parallel sides, enlarge and clean holes.

“ Shaft / arbor 3.1 mm (1/8")
“ Overall length 40mm
“ Gritted length 16.5mm
“ Widest point 7mm
(all measurements are approximate)

The FINE ROTARIES enables the user to cut thin, and fragile materials, leaving the best finish. Also, use them to debur rough cut or sawn edges.

Our Rotaries have an integral arbor, enabling them to be used in reversible drive tools.
They allow the user to cut a wide range of materials quickly and cleanly leaving an excellent finish. All rotaries are ideal for routing, shaping and removing materials without tearing or clogging.
Use on all Woods, Glass Fibre, Carbon Fibre, PCB, Kevlar, Plexiglas, Lexan, Perspex, Acrylics, Plastics, Polystyrene, Ceramics etc.
Excellent on Perspex, Plexiglass, Lexon, use below 10,000 RPM and they will not melt, crack or chip them. (not recommended for use on metal)
Note Rotaries should be fully inserted in to the chuck and tightened before using. Maximum RPM 20,000 Low - Medium.


SAFETY:- Always wear protective goggles when using Rotary Tools.
IMPORTANT:- Carbon Fibre should not be cut using an electric drill, because of the possibility of electrocution.

Manufacturer and responsible person (information obligations under the GPSR Product Safety Regulation)

HACKER Motoren GmbH
Schinderstrassl 32
84030 Ergolding
DEUTSCHLAND
Tel: 0049/871953628-0
[email protected]

PERMA GRIT Small "Dome" mounted point fine
Product number: 9789118
Manufacturer number: PG1065

€18.95*

Not in stock. Available only by special order in approx. 7 to 21 business days.

Privacy

Small Rotary
Rotary Domehead Fine finishing Grit, parallel sides, enlarge and clean holes.

“ Shaft / arbor 3.1 mm (1/8")
“ Overall length 40mm
“ Gritted length 16.5mm
“ Widest point 7mm
(all measurements are approximate)

The FINE ROTARIES enables the user to cut thin, and fragile materials, leaving the best finish. Also, use them to debur rough cut or sawn edges.

Our Rotaries have an integral arbor, enabling them to be used in reversible drive tools.
They allow the user to cut a wide range of materials quickly and cleanly leaving an excellent finish. All rotaries are ideal for routing, shaping and removing materials without tearing or clogging.
Use on all Woods, Glass Fibre, Carbon Fibre, PCB, Kevlar, Plexiglas, Lexan, Perspex, Acrylics, Plastics, Polystyrene, Ceramics etc.
Excellent on Perspex, Plexiglass, Lexon, use below 10,000 RPM and they will not melt, crack or chip them. (not recommended for use on metal)
Note Rotaries should be fully inserted in to the chuck and tightened before using. Maximum RPM 20,000 Low - Medium.


SAFETY:- Always wear protective goggles when using Rotary Tools.
IMPORTANT:- Carbon Fibre should not be cut using an electric drill, because of the possibility of electrocution.

Manufacturer and responsible person (information obligations under the GPSR Product Safety Regulation)

HACKER Motoren GmbH
Schinderstrassl 32
84030 Ergolding
DEUTSCHLAND
Tel: 0049/871953628-0
[email protected]