With the ColorMatic Clear Light Set, yellowing and dark shades can be removed quickly, easily and inexpensively. The repair takes place in the installed state, no removal necessary. After sanding and cleaning, the plastic pane can be optimally protected against UV light again with the 2K clear lacquer included in the set.
Application area:
Complete set for repairing headlights Plastic lens for front and rear lights.
QUALITY AND CHARACTERISTICS
- Complete set, contains all the components necessary for painting plastic discs
- Easy to use
- Range 190261 Plastic cleaner: about 20 headlights
- Range 359347 Plastic bonding agent: about 14 headlights
- Range 515309 2K Clear-coat headlights: about 4 headlights
- Products also available separately
- Suitable for polycarbonate plastic diffusers, front and rear lights
- Renews the UV protective layer of the headlight
- No need to remove the headlight
- Cost-effective
- Fast, painting two headlights takes about 30 minutes
PHYSICAL AND CHEMICAL DATA
190261 plastic cleaner 400 ml
- Binder base: Solvents
- Colour: transparent
- Smell: after solvent
- Yield: Very productive due to strong effectiveness
- Substrate: Indoor and outdoor plastics
- Shelf life/storage: 10 years if properly stored (=10°-25°C, maximum relative humidity of 60%)
- Container/contents: aerosol cans, maximum nominal volume 400 ml
- VOC value: 300g
359347 Plastic bonding agent 150 ml
- Binder base: polyolefin resin
- Colour: transparent
- Smell: after solvent
- Yield: 400 ml = 3 - 4 m² / 150 ml = about 2 m²
- Substrate: PP, PP/EPDM, ABS, SAN, PC, PA, PUR-RIM, R-TPU, PPO, PBT, PUR flexible foam, UP-GF plastics
- Shelf life/storage: 10 years if properly stored
- Container/contents: aerosol cans, maximum nominal volume 400 ml and 150 ml
- VOC value: 111.0 g
515309 2K headlight clear coat, 200 ml
- Binder base: Acrylic
- Colour: transparent
- Smell: after solvent
- Gloss level: in 60° measuring angle according to DIN 67530
- glossy: 85 GE
- Yield: 200 ml for about 0.3 - 0.4 m² / 500 ml for about 0.8 - 1.0 m²
- Substrate: Solvent and water-based base coats
- Drying (at 20°C, 50% relative humidity): Dust dry: after 5 minutes / Handle-proof: after 5 hours / The drying time depends on the ambient temperature, the humidity and the applied layer thickness.
- Temperature resistance: up to 120°C
- Shelf life/storage: 36 months if properly stored (=10°-25°C, maximum relative humidity of 60%)
- Container/contents: 2 components aerosol cans, maximum nominal volume 200 and 500 ml
- VOC value: 118.6g
- Pot life: 24 hours at room temperature (20 - 25°C) / 5 days at cool storage (6°C) / Bring to room temperature (20 - 25°C) before repeated processing. See instruction manual
ENVIRONMENT AND LABELLING
Environmentally friendly:
European Aerosols strives to use formulations without regulated or questionable ingredients, with the best possible performance. The caps and packaging are made of recyclable materials.
Disposal:
Please only recycle empty containers and bring containers with leftovers to the problem waste site.
Only for DE: In order to ensure a high recycling and recycling rate, the legislature requires, according to 15 - VerpackG, paragraph 1, the return of transport, sales or outer packaging, alternatively, deviating agreements can be made.
Labeling:
All products from European Aerosols comply with the current status of the labelling regulations. The classification, classification and labelling is carried out according to GHS or CLP 1272/2008/EC in the current valid form. The safety data sheets comply with REACH 1907/2006/EC, Article 31 and Annex II, in the currently valid form.
INSTRUCTION MANUAL
Always read and observe the guidelines carefully before use!
You will find the exact instructions in your set in printed form, a movie can also be seen on YouTube.
Mixing the A component with the hardener:
- Before activating the A component, be sure to shake the can until the internal mixing spheres are clearly audible.
- Remove the protective cap on the bottom of the can and use the inserted ring to pull the pin out as far as it will go. Thus, the knife located inside the cartridge is set up and pierces the wall of the aluminum cartridge.
- By a subsequent 360° rotation, the cartridge is completely opened and the hardener is released.
- By shaking the can vigorously (2 minutes), the A component is now mixed with the hardener in the correct, predetermined mixing ratio.
- Test spraying
- Pot life: 24 hours (20°C)
- Only for use by a professional
- Wear a suitable respirator (we recommend type A2/P3)
TIPS FOR USEBefore use, bring the can to room temperature (20 - 25°C) and place it in lukewarm water.
For an optimal painting result, we recommend a temperature of 20 - 25°C and a relative humidity of 45 - 60%.
Attention: High humidity can lead to loss of gloss!
