NEWS

Intended use
Mipa Grundierfiller-Spray is a fast-drying chromate-free one-component anti-corrosion primer filler based on synthetic resin. Especially suitable as adhesion promoter for minor repairs and sand through areas.

Characteristics

• Excellent corrosion protection
• Very high filling and hiding power
• Fast drying
• Easy to sand
• Good adhesion to iron and steel
• Overcoatable with Mipa BC paints
• Colour / gloss level: beige / matt

Processing instructions:

Substrates
Iron and steel

Pre-treatment / cleansing
Pre-clean with Mipa Silikonentferner.
Please refer to the section "Substrate preparation" for detailed information.

Preparation
Before use, shake can vigorously for 1 - 2 min!

Application
Spray to test - spray distance approx. 20 - 30 cm
2 - 3 coats, dry film thickness: 50 - 60 ?m

Flash-off time
3 - 5 min between coats

After use
After use, turn can upside down and spray until the valve is clean, this prevents the valve from clogging up.

Drying time at 20 °C
Dust dry after approx. 10 - 15 min
Set to touch after approx. 60 min
Sandable after approx. 60 min
Overcoatable after approx. 60 min

Subsequent processing
Dry sanding:
For 1-layer topcoats P 400
For 2-layer topcoats P 500 - 600

Wet sanding:
For 1-layer topcoats P 600
For 2-layer topcoats P 800 - 1000

Processing conditions
From +10 °C and up to 80 % relative humidity. Ensure adequate air ventilation.

Storage
Can be stored for 2 years in cool and dry places.

VOC-regulation
EU limit value for the product (cat. B/e): 840 g/l
This product contains max. 700 g/l of VOC.

Processing instructions:

Do not overcoat with polyester-based materials,

Substrate preparation:
The substrate must be clean and dry. Remove oil, grease, rust, mill skill, rolling skin as well as other substances impairing the function of the coating!

Remove old coatings or primers that have not cured or are not sound.

Do not use on thermoplastic substrates.

Steel substrates:
1. Pre-clean with Mipa Silikonentferner.
2. Then dry sand with P 120.
3. Afterwards, degrease with Mipa Silikonentferner.

GRP:
1. Before painting, reheat the object to be painted for 60 minutes at 60°C.
2. Degrease with Mipa Kunststoffreiniger antistatisch or Mipa Silikonentferner.
3. Sand thoroughly with P 240 - P 320.
4. Clean again with Mipa Kunststoffreiniger antistatisch or Mipa Silikonentferner.
5. Allow parts to dry completely.
6. Recommended for neutralising electrostatic charges: Blow off the surfaces by means of MP Ionisierungspistole X-ION, cleans and neutralises in one operation, reduces dust
inclusions when coating. In addition, this avoids differences in pigment orientation when overcoating with metallic/ effect basecoats.

ATTENTION:
Releasing agents must be removed completely! After the previously mentioned preparation, we recommend doing a wetting test with water. If the water drops roll off quickly, repeat the pre-treatment.

Intact, sound old paintworks, factory paintings:
1. Pre-clean with Mipa Silikonentferner.
2. Then sand with P 320.
3. Afterwards, degrease with Mipa Silikonentferner.

Cathodic e-coating / shop primer:
1. Pre-clean with Mipa Silikonentferner.
2. Then sand with MP Softpad Superfine or with P 320.
3. Afterwards, degrease with Mipa Silikonentferner.

When used as sanding filler, follow the sanding instructions below after drying:
1. For 1-layer topcoats, sand dry with P 400 or wet with P 600.
2. For 2-layer topcoats, we recommend dry sanding with P 500 / 600 or wet sanding with P 800 / 1000.
3. Thoroughly remove sanding dust using Mipa Silikonentferner or Mipa WBS Reiniger or Mipa WBS Reiniger FINAL. Use clean, lint-free wiping cloths.

It is recommended that the sanded surfaces and/ or joints, grooves etc. are thoroughly blown off with oil-free compressed air.

4. Then clean the surface to be painted with Mipa Silikonentferner, Mipa WBS Reiniger or Mipa WBS Reiniger FINAL using a new, clean cloth.

Once the cleaners have dried completely without leaving streaks, apply the topcoat.


2.2 Label elements 3/2021
· Labelling according to Regulation (EC) No 1272/2008
The product is classified and labelled according to the CLP regulation.

Signal word Danger

Hazard-determining components of labelling:
acetone
Hydrocarbons, C9, aromatics
n-Butyl acetate
2-Butanone oxime

Hazard statements
H222-H229 Extremely flammable aerosol. Pressurised container: May burst if heated.
H315 Causes skin irritation.
H319 Causes serious eye irritation.
H317 May cause an allergic skin reaction.
H336 May cause drowsiness or dizziness.
H412 Harmful to aquatic life with long lasting effects.

Precautionary statements
P101 If medical advice is needed, have product container or label at hand.
P102 Keep out of reach of children.
P103 Read label before use.
P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
P211 Do not spray on an open flame or other ignition source.
P251 Do not pierce or burn, even after use.
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
P410+P412 Protect from sunlight. Do not expose to temperatures exceeding 50 °C/122 °F.
P501 Dispose of contents/container in accordance with local/regional/national/international regulations.

Additional information:
Buildup of explosive mixtures possible without sufficient ventilation.

2.3 Other hazards
· Results of PBT and vPvB assessment
· PBT: Not applicable.
· vPvB: Not applicable.