FREE SHIPPING from € 100,- / DE / AT

FREE SHIPPING: DE, AT... from 100,- € / CH ... from 199,- / FR, BE, BG, FR, IT, HR, NL ... from 299,- €

FREE SHIPPING from € 100,- / DE / AT

-16%

Bearing: ••
Servo Speed sec./60° (6,6V) HV: 0,11
Servo Speed sec./60° (7,4V) HV: 0,09
Servo Torque kg/cm (6,6V) HV: 11,4
Servo Torque kg/cm (7,4V) HV: 13,8
Gearbox Type: Metal
Weight (g): 54
Length (mm): 40
Wide (mm): 20
Height (mm): 40
Servo type: High Voltage
Gear tooth: 25
Betriebspannung (V) HV: 4,8 - 8,4

Powerful and fast Servo S 9470 SV HV S-BUS 2 for 1/10 cars in high voltage and S.BUS version, for direct operation with 2S LiPo batteries. With double ball-bearing metal gear unit and water-protected housing. Specially designed mounting flanges with integrated damping keep unwanted vibrations away from the servo to a greater extent than was previously customary. High voltage version of the model S9451, programmable!

The following functions can be set:
- S.BUS channel assignment
- Servo polarity
- Soft start, on-off
- Mode selection on signal failure Hold or Free
- Soft servo run, on-off
- Servo position (servo tester)
- Servo center adjustment +/- 300 µs (approx. 30 degrees)
- Servo speed, 0.39...9 seconds per 45 degrees
- Deadband setting
- Servo travel adjustment left and right separate, approx. 50...150% (total travel = 180 degrees)
- starting power
- cushioning
- holding force
- ID storage

New:
With the new FASSTest T18MZ and FX-32 remote control systems, the new S.BUS2 servos (SV) can now also be programmed as retractable landing gear servos (de-energised after 15 seconds).
Alternatively, a current overload protection can be set O.L.P
SBUS2 servos (SV) can be operated either at the S.BUS1 or S.BUS2 output of the receivers. In the case of S.BUS2 also in mixed operation with telemetry sensors.

Addressing with the S-BUS channel number can be done in different ways:
Via the S.BUS receiver, with the SBC-1 No. F1696 programmer, via the PC/S-Link software, USB adapter CIU-2, No. F1405 required, and on the S.BUS connection of new transmitters such as T10J, T14SG, T18MZ, FX-32, FX-22, etc.

The servos can also be programmed in the installed and wired state by calling up and addressing the servo via the individual ID.
Of course, all S.BUS servos can be connected to conventional receivers with PWM modulation.


Manufacturer and responsible person (information obligations under the GPSR Product Safety Regulation)

Minicars Hobby Distribution AB
Annelundsgatan 17C
74940 Enköping
SCHWEDEN
Tel: 0046-0171143000
[email protected]

FUTABA S 9470 SV HV S-BUS 2 DIGITAL SERVO
Product number: 9718953
Manufacturer number: FPS9470SV

€93.99*

% €112.50* (16.45% saved)

Prices incl. VAT plus shipping costs

Not in stock. Available only by special order.

Privacy

Bearing: ••
Servo Speed sec./60° (6,6V) HV: 0,11
Servo Speed sec./60° (7,4V) HV: 0,09
Servo Torque kg/cm (6,6V) HV: 11,4
Servo Torque kg/cm (7,4V) HV: 13,8
Gearbox Type: Metal
Weight (g): 54
Length (mm): 40
Wide (mm): 20
Height (mm): 40
Servo type: High Voltage
Gear tooth: 25
Betriebspannung (V) HV: 4,8 - 8,4

Powerful and fast Servo S 9470 SV HV S-BUS 2 for 1/10 cars in high voltage and S.BUS version, for direct operation with 2S LiPo batteries. With double ball-bearing metal gear unit and water-protected housing. Specially designed mounting flanges with integrated damping keep unwanted vibrations away from the servo to a greater extent than was previously customary. High voltage version of the model S9451, programmable!

The following functions can be set:
- S.BUS channel assignment
- Servo polarity
- Soft start, on-off
- Mode selection on signal failure Hold or Free
- Soft servo run, on-off
- Servo position (servo tester)
- Servo center adjustment +/- 300 µs (approx. 30 degrees)
- Servo speed, 0.39...9 seconds per 45 degrees
- Deadband setting
- Servo travel adjustment left and right separate, approx. 50...150% (total travel = 180 degrees)
- starting power
- cushioning
- holding force
- ID storage

New:
With the new FASSTest T18MZ and FX-32 remote control systems, the new S.BUS2 servos (SV) can now also be programmed as retractable landing gear servos (de-energised after 15 seconds).
Alternatively, a current overload protection can be set O.L.P
SBUS2 servos (SV) can be operated either at the S.BUS1 or S.BUS2 output of the receivers. In the case of S.BUS2 also in mixed operation with telemetry sensors.

Addressing with the S-BUS channel number can be done in different ways:
Via the S.BUS receiver, with the SBC-1 No. F1696 programmer, via the PC/S-Link software, USB adapter CIU-2, No. F1405 required, and on the S.BUS connection of new transmitters such as T10J, T14SG, T18MZ, FX-32, FX-22, etc.

The servos can also be programmed in the installed and wired state by calling up and addressing the servo via the individual ID.
Of course, all S.BUS servos can be connected to conventional receivers with PWM modulation.


Manufacturer and responsible person (information obligations under the GPSR Product Safety Regulation)

Minicars Hobby Distribution AB
Annelundsgatan 17C
74940 Enköping
SCHWEDEN
Tel: 0046-0171143000
[email protected]

This website uses cookies to ensure the best experience possible. More information...