Skip to main content

FREE SHIPPING from € 100,- / DE / AT

FREE SHIPPING: DE, AT... from 100,- € / CH ... from 199,- / FR, BE, BG, FR, IT, HR, NL ... from 299,- €

FREE SHIPPING from € 100,- / DE / AT

Quantity / Length in meters: 400 g
Content sufficient for: 320 g Formenharz P + 80 g Härter P-25
Besondere Kennzeichnung: EUH205
Gefahrenhinweise: H302, H312, H314, H315, H317, H318, H332, H411, H412, H319
Sicherheitshinweise: P260, P303+P361+P353, P310, P405, P305+P351+P338, P501, P333+P313
Piktogramme: GHS05, GHS07, GHS09

Please be aware that this product can only be shipped to the following countries: Austria, Germany, Switzerland, Belgium, Bulgaria, Croatia, Czech Republic, Denmark, France, Greece, Hungary, Italy, Luxembourg, Netherlands, Norway, Poland, Portugal, Romania, Serbia,  Slovakia, Slovenia, Spain, and the United Kingdom,Ireland!

Please be aware that this product can only be shipped to the following countries: Austria, Germany, Switzerland, Frankreich, Italy, Slovakia, Slovenia, Poland, Croatia, Netherlands, Romania, Czech Republic and Hungary!

Mould resin P

  • Hard elastic, good edge strength
  • Excellent grinding and polishing properties (Shore D-Hardness Ø 75)
  • Thixotropic (non-drip)
  • Manufactured in a vacuum, so optimally free of air bubbles and homogeneous

This two-component epoxy resin is coloured black for gel coats in-mould construction with high edge strength and good polishing properties. Mould resin P is processed and cured at room temperature in conjunction with epoxy resin laminates and laminating ceramics. In contrast to resin and metal systems, the surfaces are polishable. This tooling gel coat is hard-elastic, i.e. not brittle, and exhibits good edge strength.

  • Consumption: approx. 0.6 kg/m² (thickness Ø 0.5 mm)

Hardener P-25
Hardener for Mould Resin P with a pot life of 20 minutes.

  • Excellent chemical resistance (as far as possible styrene-resistant)
  • Free of nonylphenol and benzyl alcohol

  • Mixing ratio: 100 : 25 parts by weight of resin to hardener
  • Processing time (100 g preparation at 20 °C): 20 minutes
  • Gel time (at 20 °C/1 mm layer thickness): approx. 2 hours
  • Curing time (at 23 °C): 24 hours
  • Temperature resistance: 70 °C

Processing instructions in GFK mould construction
Error-free application is possible on most release agents. If "eyes" should nevertheless form due to poor wetting of the substrate, the second layer of mould resin can be applied to the still sticky layer after gelation (several hours curing at room temperature). If two coats are applied, any imperfections are removed.

Procedure
1. apply mould resin with a brush, layer thickness approx. 0.5 mm, allow to gel (approx. 2 h at room temperature)
2. if defects ("eyes") are formed due to the release agent, apply the second layer of mould resin, allow to gel
3. apply resin-rich coupling layer of laminating resin, glass fibre shavings + cotton flocks several mm thick
4. place glass fabric in the wet coupling layer and laminate on further layers of glass for reinforcement

Carry out all work wet-in-wet so that the layers adhere well to each other.

Other structures are of course possible. Depending on the size and geometry of the mould, other build-ups are possible:
  • Laminate directly onto the mould resin, but starting with very fine fabric so that the structure does not push through.
  • Laminate made of carbon fibre fabric, low mould weight, high rigidity.
  • Laminate made of carbon fibre fabric and aramid honeycomb as an intermediate layer, very low mould weight with high stiffness.
  • Laminate made of laminating ceramics; fast assembly, very stiff, but also higher mould weight.
  • Massive, stiff moulds made of mould resin with a thick-walled backing of resin and fillers such as sand, Poraver and similar.


Manufacturer and responsible person (information obligations under the GPSR Product Safety Regulation)

R&G
Faserverbundwerkstoffe GmbH
Im Meißel 7-13
71111 Waldenbuch
DEUTSCHLAND
Tel: +49/7157/53046-0
[email protected]

R&G Formenharz P + Härter P-25, Packung/ 400 g
Product number: 9799073
Manufacturer number: 1151540

€20.03*

Only a few left in stock, ready for shipment within 1 working day. Delivery time 1-3 working days.

Quantity / Length in meters: 400 g
Content sufficient for: 320 g Formenharz P + 80 g Härter P-25
Besondere Kennzeichnung: EUH205
Gefahrenhinweise: H302, H312, H314, H315, H317, H318, H332, H411, H412, H319
Sicherheitshinweise: P260, P303+P361+P353, P310, P405, P305+P351+P338, P501, P333+P313
Piktogramme: GHS05, GHS07, GHS09

Mould resin P

  • Hard elastic, good edge strength
  • Excellent grinding and polishing properties (Shore D-Hardness Ø 75)
  • Thixotropic (non-drip)
  • Manufactured in a vacuum, so optimally free of air bubbles and homogeneous

This two-component epoxy resin is coloured black for gel coats in-mould construction with high edge strength and good polishing properties. Mould resin P is processed and cured at room temperature in conjunction with epoxy resin laminates and laminating ceramics. In contrast to resin and metal systems, the surfaces are polishable. This tooling gel coat is hard-elastic, i.e. not brittle, and exhibits good edge strength.

  • Consumption: approx. 0.6 kg/m² (thickness Ø 0.5 mm)

Hardener P-25
Hardener for Mould Resin P with a pot life of 20 minutes.

  • Excellent chemical resistance (as far as possible styrene-resistant)
  • Free of nonylphenol and benzyl alcohol

  • Mixing ratio: 100 : 25 parts by weight of resin to hardener
  • Processing time (100 g preparation at 20 °C): 20 minutes
  • Gel time (at 20 °C/1 mm layer thickness): approx. 2 hours
  • Curing time (at 23 °C): 24 hours
  • Temperature resistance: 70 °C

Processing instructions in GFK mould construction
Error-free application is possible on most release agents. If "eyes" should nevertheless form due to poor wetting of the substrate, the second layer of mould resin can be applied to the still sticky layer after gelation (several hours curing at room temperature). If two coats are applied, any imperfections are removed.

Procedure
1. apply mould resin with a brush, layer thickness approx. 0.5 mm, allow to gel (approx. 2 h at room temperature)
2. if defects ("eyes") are formed due to the release agent, apply the second layer of mould resin, allow to gel
3. apply resin-rich coupling layer of laminating resin, glass fibre shavings + cotton flocks several mm thick
4. place glass fabric in the wet coupling layer and laminate on further layers of glass for reinforcement

Carry out all work wet-in-wet so that the layers adhere well to each other.

Other structures are of course possible. Depending on the size and geometry of the mould, other build-ups are possible:
  • Laminate directly onto the mould resin, but starting with very fine fabric so that the structure does not push through.
  • Laminate made of carbon fibre fabric, low mould weight, high rigidity.
  • Laminate made of carbon fibre fabric and aramid honeycomb as an intermediate layer, very low mould weight with high stiffness.
  • Laminate made of laminating ceramics; fast assembly, very stiff, but also higher mould weight.
  • Massive, stiff moulds made of mould resin with a thick-walled backing of resin and fillers such as sand, Poraver and similar.


Manufacturer and responsible person (information obligations under the GPSR Product Safety Regulation)

R&G
Faserverbundwerkstoffe GmbH
Im Meißel 7-13
71111 Waldenbuch
DEUTSCHLAND
Tel: +49/7157/53046-0
[email protected]